Clik here to view.
Optimization Question
I'm just trying Homeseer to see if it works in my house and it's not going as well as I would have hope. I'm getting very poor network range (less than 9 metres between nodes) and strange optimization...
View ArticleRequest for those requesting help
I typically read at least the title of every new post on this message board. I've been seeing the following behavior more recently in the past for whatever reason -- and also have seen some (more?)...
View ArticlePlug-in not working all of October
Version 1.0.16280.317 The plug-in has not worked all month. I have a Craftsman door opener. Since the update to the new API it had been intermittent. It would error, I would disable it for a day, then...
View ArticleDid I lose my z-stick?!?!
Sorry if I'm on the wrong board, but I could not identify where to post this question. I have an HS3 system using an Aeon Z-Stick; this system is in a second home 1,000 miles away. This morning while...
View ArticleHow can I retrieve Micro Dimmer IDs?
So I've installed 4 micro dimmers above ceilings to control spots. and programmed 2 micro remotes to control them. Remotes to dimmers work fine. Now I'd like to create the dimmer devices in HS. I...
View ArticleTrane TCONT624 T-Stat
I've been able to include/discover 5 Trane TCONT624 thermostats successfully into my HS3 ZEE S2, but the space temperature device on each one came in as an "Unknown Subtype" and reads a value of "0"....
View ArticleTurned TV On
Good news, just bought a Samsung TV and I was able to turn it on by sending a Wake on LAN packet through HS. Going to do some more testing but very promising.
View ArticleGraber virtual cord z wave shades compatibility?
Hi guys, I have been doing a lot of research on z wave controlled shades and blinds. I found some articles in this forum with custom roller builds. With automation becoming more popular, manufactures...
View Articlequestions
I am transitioning from my LEDAM (HS2) setup to (HS3)BLLED. I have two signs both serial connected. One of the signs always says initialize on the Maintain LED Sign page. Both have been initialized and...
View ArticleUltraMon Stopped Identifing new Devices on the network
I have 2 days left of the trial period and UltraMon has stopped identifying new MAC address that have registered on the network. It had been working fine up to that point. Anytime a new device, that...
View Articlehs.PluginFunction or capi to control thermostat setpoint
So I'd like to pass a parm (set point) to my Z-wave thermostat in a script. Is it recommended to use hs.PluginFunction or CAPI for this? Robert
View ArticleInsteon on at ramp rate not working
I tried to set an event to turn on a light at a specified ramp rate and it doesn't seem to be working. The device is a Dual-Band LampLinc fw43. Normal on and off commands work fine. The comm...
View ArticleClik here to view.
Control house modes using Alexa (HA-bridge only)
I wanted to control devices in my house using modes to set thermostats and arming my security system just by speaking to my Amazon Echo. What I found was I could do this by setting up HS events and...
View ArticleClik here to view.
DS10 with current sensor Active Zone
I am monitoring the power state of TVs, Amplifiers, & a steam generator with an DS10. DS10 is connected to a current sensor. I have added the DS10 to BLRF and then to BLRADAR. Each one is part of...
View ArticleWeatherXML - Download Maps: Index was outside the bounds of the array.
I've been getting this error in my logs once every minute for the past few months. I'm not sure where to go to troubleshoot. If I go to the maps tab of the plugin setup, I get another error on screen,...
View ArticleContinuous setting of set points
:confused:I have two HVAC unit with separate schedules. One units has no issue with the scheduled changes, the other the set point does not update. At the thermostat early this morning I could set the...
View Articlespeaker client on android?
Ok I have been searching for an hour, how to I add my android running Hstouch as a speaker client?!?!? I see lots of posts about it but no instructions how to add it. Thanks in advance
View ArticleI presume HS does not support true X10 protocal
I have a XTB232, which operates with pure X10 commands from day one of HS3 it can take up to 40 minutes for HS to turn a light on :eek: and the log fills as below, I have only pasted a clip but the...
View ArticleNew log entries after installing beta 3.0.0.104
I mistakenly thought these entries were created by Blade's BLStat, but it appears they are being generated by the HSTouch server plug-in. I am only guessing, but they all started on the 26th when I...
View Articleshould I move my z-net
I system appears very solid from the Node Info. I have run Z-health for a couple of days (now I have disabled). 80% of the time the system response is accurate and fast. The remaining 20%of the time I...
View Article